If you have ever looked around an attic with a flashlight, you may have noticed small metal clips shaped like the letter H sitting between the edges of the roof sheathing panels. These are H-clips, also called panel edge clips. They are inexpensive and easy to overlook, but they do two useful jobs, and on some roofs the panel manufacturer requires them.
This guide explains what H-clips do, when they are needed, what it means when we find them missing during an inspection, and what can be done about it.
What H-clips do
Most roofs in Fargo-Moorhead are sheathed with 4-by-8-foot panels of OSB or plywood nailed across the rafters or trusses. The short ends of each panel land on a rafter or truss, but the long edges run between the framing members with nothing underneath them. H-clips slide onto those long edges between the rafters, so each panel helps hold up its neighbor.
That gives you two benefits:
- Stiffer panel edges. The clip ties two panel edges together, so one edge is less likely to sag or flex below the other between rafters.
- The right gap. APA, the Engineered Wood Association, recommends a 1/8-inch space at all panel edge and end joints unless the panel manufacturer says otherwise. Wood panels grow slightly as they take on moisture, and the gap gives them room so they don’t push against each other and buckle. The body of the clip sets that space automatically.
Clips are not the only way to support panel edges. APA lists three accepted methods: panels with tongue-and-groove edges, panel edge clips, and lumber blocking nailed between the rafters under the joint.
When H-clips are needed
Whether a roof needs edge support depends on three things: the panel’s span rating, its thickness and how far apart the rafters or trusses are. Every APA-rated panel carries a stamp with a span rating such as “24/16” or “32/16”. The first number is the maximum spacing of roof supports in inches.
APA’s recommended maximum roof spans show how edge support changes the answer:
| Panel span rating (typical thickness) | Maximum span with edge support | Maximum span without edge support |
|---|---|---|
| 24/0 (3/8 inch) | 24 inches | 19.2 inches |
| 24/16 (7/16 inch) | 24 inches | 24 inches |
| 32/16 (15/32 inch) | 32 inches | 28 inches |
| 40/20 (19/32 inch) | 40 inches | 32 inches |
When edge support is called for, APA recommends one clip midway between each pair of supports, or two equally spaced clips when the supports are 48 inches or more apart.
The panel manufacturer’s instructions also matter, and some are stricter than the general table. Huber, for example, requires edge support for its 7/16-inch ZIP System roof sheathing when supports are more than 16 inches on center, and says that skipping it voids the product’s warranty. Building codes, including the International Residential Code that residential codes in North Dakota and Minnesota are based on, also use span ratings to set how far roof sheathing may span.
The short version: on some roofs H-clips are optional, and on others they are required. The panel stamp and the manufacturer’s installation instructions tell you which.
What this finding means in an inspection report
When we find no H-clips, tongue-and-groove edges or blocking at the long edges of the roof sheathing during an inspection, we note it. From the attic we can usually see the framing spacing and often the panel stamp, but we can’t always confirm which manufacturer’s instructions apply or what was approved for that roof. The finding means the edge support should be checked against the panel’s span rating and the manufacturer’s requirements.
Missing clips don’t mean the roof is failing. Many roofs without clips perform well for years. Where edge support was needed and left out, though, it can lead to:
- Panel edges that sag between rafters, which can show as a wavy roof line from outside
- One panel edge sitting higher than the next, which can show through the shingles as a ridge
- Panels butted tight with no gap, which can buckle when they swell with moisture
Attic moisture makes these problems worse. Wood panels are less stiff when they are damp, and in our climate attic frost can wet the underside of the sheathing every winter. Our articles on attic ventilation and frost in the attic explain how to keep the attic dry.
How missing edge support is fixed
H-clips go on as the panels are installed, so they can’t simply be added from the attic later. If a roofer or contractor finds that edge support is needed, the usual options are:
- Lumber blocking from the attic. Short pieces of lumber are fitted and fastened between the rafters or trusses under the unsupported panel edges. This works when the attic is accessible.
- Clips at the next reroof. When the old shingles come off, the sheathing can be inspected, damaged panels replaced, and clips or blocking added where needed.
- Monitoring. On a roof with no sagging, no buckling and panels that meet the span rating without edge support, a contractor may advise simply watching it.
If you see sagging between rafters, soft spots when walking on the roof or water stains on the sheathing, have a qualified roofing contractor look at it, and a structural professional if the framing itself looks affected.
Tips for buyers, homeowners and new construction
- Look for the panel stamp. From the attic, the stamp on the underside of the sheathing usually shows the span rating and thickness.
- Building new? Ask your builder which sheathing is going on the roof and whether its instructions call for edge clips. A pre-drywall inspection or new construction inspection is a good time to check, while the attic is still easy to see.
- Under warranty? A builder’s warranty inspection before the warranty ends gives you a list to take to the builder.
- Planning a new roof? Ask the roofer to check the sheathing edges while the deck is exposed. If you are adding insulation to the underside of the roof deck, read about spray foam on the roof deck first.
H-clips: common questions
Are H-clips required by code?
Sometimes. It depends on the panel’s span rating and thickness, the rafter or truss spacing and the manufacturer’s installation instructions. Where the span is greater than the panel can carry without edge support, the edges need clips, tongue-and-groove edges or blocking.
Can H-clips be installed after the roof is on?
Not easily, because the clips fit onto the panel edges as the panels go down. Lumber blocking installed from the attic is the usual fix on a finished roof, or clips can be added when the roof is replaced.
Do H-clips make the roof stronger?
They support the panel edges and allow the panels to span farther between supports. Huber notes that edge support does not increase the maximum load a roof panel can carry; it allows wider spacing of the supports.
How many H-clips should there be?
APA recommends one clip midway between each pair of supports, and two equally spaced clips when the supports are 48 inches or more apart.
My roof has no H-clips. Should I worry?
Not necessarily. Check the panel stamp and the framing spacing, and look for sagging or buckling. If anything looks off, have a roofing contractor evaluate it.
Want a closer look at the roof structure of a home you are buying or building? Learn more about our new construction inspection and home buyer’s inspection.
Sources
- APA – The Engineered Wood Association. Engineered Wood Construction Guide, roof excerpt (Form E30X, revised December 2019), Table 33 and Figure 21.
- APA – The Engineered Wood Association. Panel Edge Support for Narrow-Width Roof Sheathing, Technical Note R275.
- Huber Engineered Woods. ZIP System Technical Tip: Do I Need H-Clips?
- Journal of Light Construction. JLC Field Guide: Sheathing and Shear Panel (January 2023).