Mold test results can be hard to read. A lab report full of Latin names, spore counts and columns of numbers looks precise, yet there is no official number that says a home is safe or unsafe. This guide walks through what each part of a mold lab report means, how professionals compare indoor and outdoor samples, which molds point to water damage, and why one number never tells the whole story.
Nordic Inspections · Fargo-Moorhead
Worried about mold in your home?
Tell us what you’re seeing or smelling and we’ll recommend the right next step. If you need one, a preliminary mold inspection finds the moisture and the growth, and only takes samples where they answer a real question.
Questions first? Call (701) 566-1446
Got mold test results? Start here
- Find the outdoor sample. Indoor air results only make sense next to an outdoor sample from the same visit.
- Look for water-damage molds. Stachybotrys or Chaetomium indoors says more than a big count of common outdoor types.
- Read the notes. Check the debris rating, and whether a tape lift was marked as containing hyphae or fruiting structures.
- Match the numbers to the building. Results should line up with moisture readings, stains, odors and leak history before anyone plans remediation.
Why mold test results don’t come with a “safe” number
The first thing to know is that no government agency has set a limit for mold spores indoors. The U.S. EPA says that “standards or Threshold Limit Values (TLVs) for airborne concentrations of mold, or mold spores, have not been set.” The CDC notes that there are no set standards for what is an acceptable amount of mold in a home, and NIOSH says there are “no health-based standards for mold” in indoor air.
The World Health Organization reviewed the research in 2009 and concluded that no health-based threshold for mold in buildings can be recommended. Health Canada reached a similar view: people respond to mold so differently that exposure limits can’t be set, and air test results “cannot be used to assess risks to the health of building occupants.”
So when a lab report says “high” or a website labels a count “dangerous,” that label comes from a lab category or someone’s rule of thumb, not from a health standard. Mold test results are evidence about a building. They are read by comparing samples to each other and to what the inspection found, not by checking a single number against a chart.
The parts of an air sample report
Most mold air tests in homes use a spore trap: a pump pulls a measured amount of air through a small cassette, and spores and particles stick to a sticky slide inside. The lab then counts and identifies what it sees under a microscope. EMSL Analytical, the lab Nordic uses, lists the ASTM D7391 method on its spore trap reports. Here is what the main columns and notes on a typical spore trap report mean.
- Sample ID, location and volume. Each sample is tied to a room (or “outdoor”) and to the volume of air collected, in liters. The AIHA notes that a typical spore trap sample runs for five to 15 minutes.
- Spore types. Spores are grouped by genus or by look-alike groups, such as Cladosporium, Ascospores or Basidiospores. Our fungal glossary explains the common names you will see.
- Counts per cubic meter. The lab converts what it counted on the slide into spores per cubic meter of air (counts/m³). A modest count on the slide can become a large-looking number after that conversion.
- Analytical sensitivity. The smallest count the method can report for that sample. On an EMSL sample report, for example, one spore counted at 300x magnification equals 21 counts per cubic meter. Results near this level are close to “one spore seen.”
- Background debris. A rating of how much dust and other particles covered the slide, from 1 (low) to 4 (high), with 5 meaning “overloaded.” The ASTM method notes that heavy debris tends to hide spores, so counts on a heavily loaded slide may read low.
- Hyphal fragments. Pieces of the thread-like body of mold, not spores. They are counted separately.
- Aspergillus/Penicillium. These two are reported together because, as the AIHA puts it, their spores “cannot be reliably distinguished” under the microscope. Both are common indoors and outdoors.
You may also see a line saying interpretation of the results is the responsibility of the client. That is standard: the lab counts what is on the slide, and the person who took the samples interprets them in light of the building.
How indoor and outdoor samples are compared
The heart of reading air results is the outdoor comparison, which is why a sample taken outside at the same visit matters so much. The AIHA describes air sampling as collecting and comparing indoor and outdoor samples to see whether any fungal levels are significantly elevated indoors. Three things are compared.
- Total amount. In a home without a mold problem, indoor counts are usually similar to or lower than outdoors. The EPA, describing what to expect after a successful cleanup, says indoor levels should be “roughly equivalent to or lower than” outdoor levels.
- Types. The kinds of mold indoors should look like the kinds outdoors. The EPA says the types and concentrations indoors “should be similar to what is found in the local outdoor air.”
- Ranking. Professionals also compare which types are most common inside and outside. If Cladosporium leads outdoors and Aspergillus/Penicillium leads by a wide margin indoors, that difference is worth explaining, even when the indoor total is not high. Guidance compiled from New York City, EPA and OSHA sources describes this rank-order comparison, and also warns that rankings “should not be used to define ‘safe or unsafe’ concentrations.”
The comparison is a pattern, not a formula. Outdoor counts change with the weather and the time of day, and household activity changes indoor counts. That is why an indoor result that is “higher than outside” by itself is a clue to follow up, not a verdict.
Water-damage indicator molds
Some molds are common everywhere. Others grow mainly on materials that have stayed wet, so finding them indoors carries more weight even in small numbers.
- Stachybotrys (often called “black mold”) is one of the clearest examples. Quebec’s public health institute calls it “an excellent indicator of chronically water-damaged building materials” and notes that it is usually difficult to detect in air samples unless the growth is physically disturbed. That means a low air count doesn’t rule it out.
- Chaetomium grows well on cellulose building materials in water-damaged buildings, according to the same source, and releases few spores into the air until the growth dries out.
Because these molds don’t spread easily through the air, even one or two spores in an indoor sample, with none outdoors, is a reason to look harder for a wet wall, ceiling or crawlspace. It doesn’t prove there is a hidden problem, and it doesn’t measure health risk. It tells the inspector where to focus.
Not sure what your mold test results point to? A preliminary mold inspection traces the moisture and growth behind the numbers and only samples where it answers a real question. Schedule a preliminary mold inspection.
Reading tape lift and swab results
Surface samples answer a different question than air samples: is this spot mold growth, and what kind?
A tape lift is a piece of clear tape pressed on a surface. EMSL reports what it sees on the tape in categories per area analyzed: Rare (1 to 10), Low (11 to 100), Medium (101 to 1,000) and High (more than 1,000). An asterisk on EMSL tape reports means the sample “contains fruiting structures and/or hyphae associated with the spores.” That note matters, because spores alone can simply settle on a surface, while hyphae and fruiting structures suggest mold was actually growing there.
Swab samples are often sent for culture, which means the lab tries to grow what was collected. Culture results are reported in colony forming units (CFU) and can identify species, but they only show molds that grow on the lab’s media. Direct microscope counts, like spore traps and tape lifts, include spores whether or not they would grow in culture. The AIHA notes that so-called viable sampling is more accurately called culture-based analysis.
Why one number never tells the whole story
Air samples are short snapshots of something that changes all the time. The AIHA notes that samples from the same room at different times of day can vary by as much as 10,000-fold. It also estimates that sampling and analytical error for spore traps is generally between 30 and 200 percent. The EPA adds that air sampling provides information only for the moment it was taken.
Negative results can mislead too. NIOSH notes that low short-term results “may not represent actual exposures,” and that a careful visual inspection and a musty odor are more reliable than air sampling for finding mold problems. A large review led by Lawrence Berkeley National Laboratory scientist Mark Mendell in 2011 reached a similar conclusion: visible dampness, water damage, mold or mold odor are more reliable signs of mold-related health risk than current lab measurements of mold and other microbes.
In practice, that means mold test results should always be read alongside the building:
- Were the samples taken near the suspected problem, in other living areas, and outside?
- Were windows open, was it raining, or had someone just vacuumed or disturbed materials?
- Do the results match what the moisture readings, thermal images and visual inspection showed?
- Do the results fit the whole home, or only one room?
When the results and the building tell the same story, you can act with confidence. When they disagree, the building usually deserves another look before anyone spends money on remediation.
What “elevated” means, and what it doesn’t
When a report calls a result elevated, it usually means one of three things: indoor counts higher than outdoors, indoor types that differ from outdoors, or water-damage indicator molds found indoors. Any of these suggests there may be mold growth or a moisture problem in the building that should be found.
What “elevated” doesn’t mean is that the home will make someone sick, or that every material in the home needs to be removed. The AIHA is clear that air sampling “does not and cannot evaluate potential health risks.” If someone in the home has health concerns, share the results and the inspection findings with their physician. Our mold health symptoms page is a good starting point.
Remediation professionals use a related set of terms from the IICRC S520 standard. As commonly summarized, Condition 1 is a normal fungal ecology, Condition 2 is an area contaminated with settled spores from a nearby growth area, and Condition 3 is actual mold growth, visible or hidden. After a cleanup, the EPA expects indoor air to look like outdoor air in types and amounts. We cover cleanup and verification on our mold remediation page.
Five questions to ask about any mold lab report
- Was the lab accredited? The AIHA Laboratory Accreditation Programs run the Environmental Microbiology Laboratory Accreditation Program (EMLAP) for labs that analyze spore traps, tape lifts and swabs, including required proficiency testing.
- Was there an outdoor sample from the same visit? Without it, indoor air counts are hard to interpret.
- Why was each sample taken where it was? Every sample should answer a question, such as “is there hidden growth behind this stained wall?”
- Was the debris rating high? An overloaded slide can undercount spores.
- Does the written interpretation explain the results in light of the building? Numbers without moisture findings and next steps are only half an answer.
If your results came from a do-it-yourself kit or a dust test like ERMI, the reading is different. Our guides to mold testing options and ERMI and HERTSMI-2 mold tests explain what those results can and can’t show.
Our experience
At Nordic Inspections, mold inspections are led by Lars Knobloch, a Council-certified Indoor Environmentalist (CIE) through the American Council for Accredited Certification and an ASHI Certified Inspector. Lars is also a certified radon measurement professional and radon mitigation specialist, and has provided litigation support on building defects and environmental problems. Nordic Inspections has served Fargo-Moorhead and the surrounding areas of North Dakota and Minnesota since 2010. Our mold samples are analyzed by EMSL Analytical, an independent laboratory, and every set of results is explained in a written report alongside what we found in the building. Learn more about our mold inspection and testing services.
Mold test results: common questions
Is it normal to find some mold spores indoors?
Yes. Mold spores are part of outdoor air and come inside on air, clothing and pets, so nearly every indoor sample contains some. What matters is how indoor results compare with outdoors and whether water-damage molds show up.
Can I compare my numbers to a chart I found online?
Be careful. No agency has set indoor mold limits, and online charts are usually someone’s rule of thumb. The outdoor sample from the same day is the best comparison.
My results were “normal.” Does that mean there’s no mold problem?
Not necessarily. Air samples are short snapshots, and molds like Stachybotrys rarely show up in air unless disturbed. If you see staining, smell mustiness or know about past leaks, the building still deserves a careful look.
Should I retest to confirm my results?
Retesting the same way often gives a different number, because counts change from hour to hour. It is usually more useful to find and fix the moisture source, then test after cleanup to confirm the area matches outdoor air.
Do mold test results tell me whether mold is making someone sick?
No. Air sampling can’t evaluate health risk. If you are worried about symptoms, talk with your physician and share the test results and inspection findings. Our post on mold exposure symptoms and your health explains what the research does and doesn’t show.
Sources
- Mold Testing or Sampling, U.S. Environmental Protection Agency.
- Mold Remediation in Schools and Commercial Buildings, U.S. Environmental Protection Agency, EPA 402-K-01-001, 2008.
- Mold, Centers for Disease Control and Prevention.
- Mold, Testing, and Remediation, National Institute for Occupational Safety and Health (NIOSH).
- WHO Guidelines for Indoor Air Quality: Dampness and Mould, World Health Organization, 2009.
- Residential Indoor Air Quality Guideline: Moulds, Health Canada, 2007.
- FAQs About Spore Trap Air Sampling for Mold for Direct Examination, American Industrial Hygiene Association (AIHA), 2019.
- Methods for Evaluation of Indoor Mold Growth, compiled from NYC Department of Health, EPA and OSHA guidance, NYCOSH, 2013.
- Stachybotrys chartarum and Chaetomium spp., Mould Compendium, Institut national de santé publique du Québec (INSPQ).
- Respiratory and Allergic Health Effects of Dampness, Mold, and Dampness-Related Agents, Mendell M.J. et al., Environmental Health Perspectives, 2011.
- Spore trap sample report and tape sample report, EMSL Analytical.
- ASTM D7391-17, Categorization and Quantification of Airborne Fungal Structures in an Inertial Impaction Sample by Optical Microscopy (preview), ASTM International.
- Environmental Microbiology Laboratory Accreditation Program (EMLAP), AIHA Laboratory Accreditation Programs.
- Indoor Environmental Assessments: The 3 C’s, Healthy Building Science, 2012 (summary of IICRC S520 Conditions 1 to 3).