In a Red River Valley winter, the furnace can run for months with hardly a break. Annual furnace service is the simple habit that keeps it running safely and efficiently through that stretch. It is also one of the most common recommendations we make: a furnace that needs service shows up in more than a third of the home inspections we perform.
This guide explains what a professional furnace tune-up includes, what you can do yourself between visits, the warning signs that should not wait, and what the finding means when it appears in an inspection report.
Why annual furnace service matters in a cold climate
A gas furnace burns fuel inside your home and sends the exhaust outside through a vent. When everything is clean and adjusted, that happens quietly and safely. When parts wear, vents shift or burners get dirty, the furnace can waste fuel, break down on the coldest night of the year or, in the worst case, let carbon monoxide escape.
That is why the U.S. Consumer Product Safety Commission advises homeowners to have the heating system professionally inspected and serviced every year. ENERGY STAR gives the same timing advice: check the heating system in the fall and the cooling system in the spring.
There is a cost benefit too. University of Missouri Extension notes that having heating equipment serviced before each heating season could reduce the fuel bill by as much as 10 percent.
What a furnace tune-up includes
Every company has its own checklist, but a good annual service on a gas furnace covers the safety checks and the efficiency checks. Based on the ENERGY STAR maintenance checklist and the U.S. Department of Energy’s guidance on furnaces and boilers, expect the technician to:
- Check the gas connections, gas pressure and burner combustion. A clean, properly adjusted flame burns fuel efficiently.
- Inspect the heat exchanger. A cracked heat exchanger can let combustion gases mix with the air you breathe, which is one of the main safety reasons for the visit.
- Check the vent pipe and chimney. The CPSC lists blockages, corrosion and loose or disconnected vent sections as things a yearly inspection should catch.
- Test for carbon monoxide around the furnace and vent connections.
- Tighten electrical connections and check motor voltage and current. Loose connections make parts work harder and fail sooner.
- Clean and check the blower and lubricate moving parts where the design calls for it.
- Check the condensate drain on high-efficiency furnaces, so water from the furnace drains away instead of backing up.
- Check the controls, safety switches and thermostat so the furnace starts, runs and shuts off the way it should.
- Inspect or replace the filter.
Many companies leave a service sticker or record on the furnace. When we see a current service record during an inspection, it tells us the furnace has had regular care.
What you can do between service visits
A yearly tune-up doesn’t replace a few simple homeowner habits:
- Check the filter often. ENERGY STAR suggests inspecting, cleaning or changing filters monthly, and Missouri Extension suggests checking them at least every two months during the heating season. Replace the filter whenever it looks dirty, and follow the furnace maker’s directions for size and type.
- Keep the area around the furnace clear. Don’t store boxes, paint, cleaning products or anything flammable against the furnace or water heater.
- Keep the outside vent pipes clear. Many high-efficiency furnaces have white plastic intake and exhaust pipes on the side of the house. After heavy snow or drifting, make sure they aren’t buried or iced over, since a blocked pipe can shut the furnace down.
- Keep supply and return registers open and unblocked by furniture or rugs.
- Have working carbon monoxide alarms. They are a backup, not a substitute for a well-maintained furnace.
Before you open any panel, turn the furnace off. Our article on the furnace disconnect switch explains where that switch usually is and why every furnace needs one.
Warning signs that shouldn’t wait for the yearly visit
Call a heating contractor right away if you notice any of these:
- A carbon monoxide alarm sounds. Get everyone outside first and call 911 or your gas utility from outside.
- You smell gas. Leave the house and call your gas utility from outside.
- Soot at the burner, or black stains on the outside of the chimney or flue. The CPSC lists stains and strange smells as signs that combustion gases may be leaking into the house.
- Water around the furnace, or a rusty cabinet or burner area.
- The furnace short-cycles, makes new banging or squealing noises, or keeps shutting off.
- Some rooms are much colder than they used to be, or heating bills jump without a reason.
Flu-like symptoms such as headache, dizziness, nausea and fatigue that ease when you leave the house can also point to carbon monoxide, according to the CPSC.
What “furnace service needed” means in an inspection report
When we find a furnace that is dirty, has no recent service record, shows rust or soot, or has a dirty filter, we recommend having it cleaned and serviced by a licensed HVAC contractor. A home inspection is a visual check of the furnace while it runs. We don’t take the furnace apart, test combustion or inspect the heat exchanger the way a technician does during a tune-up, so a service visit is the next step to confirm the furnace is safe and working well.
For buyers, this is usually a maintenance item rather than a major defect. It is still worth doing before your first winter in the house, and the technician can tell you more about the furnace’s condition and remaining life. Older units sometimes need more: our article on the Lennox Pulse furnace explains why some models call for heat exchanger testing.
Don’t forget the rest of the system
The furnace is only part of the heating and cooling system. The same contractor can check the air conditioner in the spring; our guide to AC condenser maintenance covers what to watch for outside. If your home has a heat recovery or energy recovery ventilator, read our guide to HRV and ERV maintenance. If the ductwork itself is a concern, see fiberglass-lined ductwork.
Annual furnace service: common questions
How often should a furnace be serviced?
Once a year, ideally in the fall before the heating season starts. The CPSC and ENERGY STAR both recommend a yearly professional check.
Is annual furnace service required for the warranty?
Some manufacturers require regular professional maintenance to keep the warranty valid. Check the warranty papers or the manufacturer’s website for your furnace, and keep your service receipts.
How often should I change my furnace filter?
Check it every month or two during the heating season and replace it when it looks dirty, or as the furnace or filter maker directs. Homes with pets, construction dust or heavy use may need more frequent changes.
Can I service my own furnace?
You can change filters, keep the area clean and keep vent pipes clear. Gas pressure, combustion, heat exchanger and carbon monoxide checks need a trained technician with the right tools.
My furnace is new. Does it still need service?
Yes. A new furnace still needs its filter changed, its condensate drain kept clear and its burners and safety controls checked. Yearly service helps it reach its full expected life.
Want a second set of eyes on your furnace and the rest of your home before winter? Schedule a homeowner inspection, or learn more about our home buyer’s inspection.
Sources
- U.S. Consumer Product Safety Commission. Carbon Monoxide Questions and Answers.
- U.S. Consumer Product Safety Commission. CPSC Urges Seasonal Furnace Inspection to Prevent CO Poisonings.
- ENERGY STAR. Maintenance Checklist.
- U.S. Department of Energy. Furnaces and Boilers.
- University of Missouri Extension. Heating System Maintenance (GH5981).